Hổ trợ trực tuyến

Mr. Hùng

Mr. Hùng


Tin tức mới

Đối tác

Đối tác

Thống kê

Đang online 5
Hôm nay 50
Hôm qua 65
Trong tuần 372
Trong tháng 745
Tổng cộng 36,780

Cảm Biến SL-V10L

Giá bán: Vui lòng gọi
Tình trạng: Mới 100%
Bảo hành: 12 Tháng
Xuất xứ: Keyence
Cảm biến an toàn Keyence Model SL-V10L



Beam axis spacing/Lens diameter

40 mm/ø5 mm 1.57" / ø0.20"

Detection capability

ø1.77" ø45 mm

Effective aperture angle

Max. ±2.5° (When operating distance is 3 m 98.23' or more)

Working distance

0.1 m to 9.0 m 0.30' to 29.53' (detection height of 1260 mm 49.61" or l ess)
0.1 m to 7.0 m 0.30' to 22.97' (detection height of 1400 mm 55.12" or more)

Response time (ms)





Light source

Infrared LED (850 nm)

Operation mode

Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)

OSSD output


2 outputs each for PNP and NPN. Can be changed by using the connector cable.

Max. l oad current

500 mA*2

Residual vol tage (during ON)

Max. 2.5 V (with a cable length of 7 m 22.97')

Leakage current

Max. 100 μA*3

Max. capacitive load

2.2 μF (with a load resistance of 100 Ω)

Load wiring resistance

Max. 2.5 Ω*4

Non safety-rel ated output


Output with automatic PNP/NPN switching function, 50 mA max.

Interlock-reset-ready output

Alarm output

Clear/blocked output

State information output 1, 2

Muting lamp output

Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)*5can be connected


EDM input

Short-circuit current 10 mA

Wait input

Short-circuit current 2.5 mA

Reset input

Muting input 1, 2

Override input

Protection circuit

Reverse current protection, short-circuit protection for each output, surge protection for each output

Approved standards



IEC61496-1, EN61496-1, UL61496-1


EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA


IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE)IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD)IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1 (Category 4, PLe)UL508UL1998


Power voltage

24 VDC +10%, -20% (Ripple P-P 10% or less)

Current consumption (mA)

When the center indicator is ON





When the center indicator is OFF





Environmental resistance

Enclosure rating

IP65 (IEC60529)

Overvoltage category


Ambient temperature

-10 to 55°C 14 to 131°F, No freezing

Ambient temperature for storage

-25 to +60°C -13 to 140°F (No freezing)

Relative humidity

15 to 85% RH (No condensation)

Storage relative humidity

15 to 95% RH

Operating ambientluminance

Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.


10 to 55 Hz, 0.7 mm 0.03" compound amplitude, 20 sweeps each in the X, Y and Z directions

Shock resistance

100 m/s2 (Approx. 10 G), 16 ms pulse in X, Y, Z directions, 1000 times each axis


Main unit case


Upper case/lower case

Zinc die-cast

Front cover

Polycarbonate, SUS304



300 g


315 g

*1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the
response times of al l the individual SL-V units, but the response time (OFF to ON) is the same
as that of a singl e SL-V unit.
e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and
SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6
ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms.
*2 When used under ambient temperature between 45 to 55°C 113 to 131°F , the maximum should not exceed 300 mA.
*3 Applies to situations when power is either off or disconnected.
*4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cabl e) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cablelength of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less.
*5 When used under ambient temperature between 45 to 55°C 113.0 to 131.0°F , use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA).
*6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by
10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the
receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of
both transmitter and receiver is fixed.)
• In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the
OFF state.
• In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON

Sản phẩm cùng loại

Đăng nhập

Tên đăng nhập / Email

Mật khẩu

Đăng nhập

Tìm kiếm sản phẩm

Từ khóa tìm

Giá sản phẩm

Tìm kiếm

Sản phẩm mới

Sản phẩm hot